BTS7960 is a high-power H-bridge driver module with thermal over-current protection. It provides a cost-optimized solution for protected high current PWM motor drives with very low board space consumption. BTS7960 circuitry with the 74HC244 chip effectively isolates the microcontroller and the motor..
Specification:
Weight: 125 gm(Approx.)
RPM: 1000
Operating Voltage: 12V DC
Gearbox: Attached Metal Gearbox
Shaft diameter: 6mm
Shaft Length: 21 mm
Torque: As per RPM
No-load current = 60 mA(Max)
Load current = 300 mA(Max).
Dimensions: Body Diameter..
Specification:
Weight: 125 gm(Approx.)
RPM: 500
Operating Voltage: 12V DC
Gearbox: Attached Metal Gearbox
Shaft diameter: 6mm
Shaft Length: 21 mm
Torque: As per RPM
No-load current = 60 mA(Max)
Load current = 300 mA(Max).
Dimensions: Body Diameter:..
DC12V24V 800L/H Solar Brushless Motor Water Pump is a centrifugal pump, the pump water flow with the increase of the head decreases. It uses advanced electronic components and a high-quality wear-resistant shaft.
Features:
High efficiency, smooth operation, and long service life.
It is lo..
DM542 DSP Digital Stepper Motor Driver is an easy-to-use professional stepper motor driver suitable for driving 2-phase and 4-phase hybrid stepping motors.
A fully digital stepper driver called the DM542 was created using a cutting-edge DSP control algorithm based on the most recent motion contro..
Double Axis Oblique Speed Reducer can directly install the wheel to make a DIY remote control car.
Features:
Shaft Diameter: 2.5 mm
Axis length: Total length 75mm, single side shaft about 28mm.
You can also use this to make other technical models that require deceleration power units, s..
The DRV8825 stepper motor driver carrier is a breakout board for TI’s DRV8825 micro-stepping bipolar stepper motor driver. The DRV8825 features adjustable current limiting, over-current and over-temperature protection, and six microstep resolutions (down to 1/32-step). It operates from 8.2 – 45 V an..
DRV8833 is a dual H-bridge motor driver IC. It is a deal driver for small motors that run on relatively low voltages. It can be used for bidirectional control of two brushed DC motors at 2.7V to 10.8V. The DRV8833 has built-in current-limiting and no need for externally supplied logic voltage.
Fe..
The Futaba Compatible S3003 Plastic Geared Servo Motor is a decent servo for every hobbyist and electronics student. The powerful motor is PWM controlled for easy interfacing.
Features:
Control System: +Pulse Width Control 1520usec Neutral
Required Pulse: 3-5 Volt Peak to Peak Square Wa..
GT Power 3-Channel Multi Servo Tester offers 3 modes to check servos or ESC. It has an Aluminum shell, durable and lightweight, easy to operate buttons. A newly upgraded servo tester. There are 3 modes to check servos or ESC i.e.manual mode, neutral mode, automatic “window wiper” mode.
It has 3 O..
This is High Torque RF 370 DC Motor, when the power supply is 6V, it is about 10000 revolutions per minute. The no-load current is 0.06A and the locked rotor current is 0.91A.
Features:
Motor Diameter: 24mm
Motor Length: 31mm (excluding shaft)
Motor Shaft Diameter: 2mm
Shaft Length: 7..
Description:
L293D Motor Driver Module is a medium power motor driver perfect for driving DC Motors and Stepper Motors. It uses the popular L293 motor driver IC. It can drive 4 DC motors on and off, or drive 2 DC motors with directional and speed control.
The driver greatly simplifies and in..