Brand: Import Dukan
Model: ID-04-341
28BYJ-48 is the most commonly used stepper motor because of its compact size, 5V power supply (that can be provided by any controller), and a high level of control. It has a stride angle of 5.625°/64, hence it will make 64 steps to complete one rotation (as every step covers 5.625) so it has a high..
₹59
Brand: Import Dukan
Model: IDC-04-343
The 28BYJ-48 Stepper Motor and ULN2003 Stepper Motor Driver is a widely popular combination of the stepper motor and stepper driver, because of the stability and reliability of the system.
28BYJ-48 is the most commonly used stepper motor because of its compact size, 5V power supply (that can be p..
₹164
Brand: Import Dukan
Model: ID-04-440
This is U Shape Fixed Mounting Bracket fits the mini 775 motors as a bracket or holder. It adopts an electroplating process and has a good anti-rust effect.
Features:
Type: U Shape Bracket
Center bench hole: the diameter is about 17.5mm
Vertical plane: 3mm thick, 52mm high, 50mm wide.
..
₹156
Brand: Import Dukan
Model: ID-04-535
A3967 Stepper Motor Driver Board provides greater flexibility and control over the stepper motor. This stepper motor driver is compatible with most microcontrollers that can output a digital 0 to 5V pulse.
Features:
Easy to interface with Arduino
Adjustable current control.
A3967 micro..
₹140
Brand: Import Dukan
Model: ID-04-545
A4950 Dual Motor Driver Module can control the positive and negative rotation of 2 motors.
Features:
Module with current limit protection
4 PWM pins are required(If you do not need to reverse, only 2 PWM pins are needed).
It is much simpler to use than the L298 and provides instructions..
₹137
Brand: Import Dukan
Model: ID-04-511
Specification:
If jumper is hit the position of ON DP, that means 16 segment (4988) or 32 segment (8825)Jm connected motor
connect 5v and 9v power supply
E, S, D, G, respectively corresponding to the connection of the Enable/Step/Dir/Gnd drive signal output
Package included:
1 ..
₹50
Brand: Import Dukan
Model: ID-04-503
The A4988 driver Stepper Motor Driver is a complete micro-stepping motor driver with a built-in converter, easy to operate. It operates from 8 V to 35 V and can deliver up to approximately 1 A per phase without a heat sink or forced air flow (it is rated for 2 A per coil with sufficient additional c..
₹55
Brand: Import Dukan
Model: ID-04-546
BTS7960 is a high-power H-bridge driver module with thermal over-current protection. It provides a cost-optimized solution for protected high current PWM motor drives with very low board space consumption. BTS7960 circuitry with the 74HC244 chip effectively isolates the microcontroller and the motor..
₹321
Brand: Import Dukan
Model: ID-05-957
Introducing a strong and effective way to drive brushless motors in a variety of applications: the DC 9-60V12V48V400W BLDC Three-phase Brushless Motor Controller. This little controller is flexible and adaptable to different systems because it is made to operate with DC power sources that vary from ..
₹1,165
Brand: Import Dukan
Model: ID-05-864
The brains behind precise motion control, the DM556 2-Phase Digital Stepper Motor Driver, is now available. This innovative driver is the perfect option for your stepper motor applications because it is designed to provide optimal performance in a small package.
The DM556 2-Phase Digital Stepper ..
₹723
Brand: Import Dukan
Model: ID-04-504
The DRV8825 stepper motor driver carrier is a breakout board for TI’s DRV8825 micro-stepping bipolar stepper motor driver. The DRV8825 features adjustable current limiting, over-current and over-temperature protection, and six microstep resolutions (down to 1/32-step). It operates from 8.2 – 45 V an..
₹81
Brand: Import Dukan
Model: ID-04-540
DRV8833 is a dual H-bridge motor driver IC. It is a deal driver for small motors that run on relatively low voltages. It can be used for bidirectional control of two brushed DC motors at 2.7V to 10.8V. The DRV8833 has built-in current-limiting and no need for externally supplied logic voltage.
Fe..
₹55
