All other 3D printer related products.
Brand: Import Dukan
Model: ID-06-439
Titan E3D 1.75mm Extruder Kit works perfectly with your installed E3D hotend, and will allow users to upgrade their 3D printer's entire extrusion system.
Features:
Type: V6 Bowden Extruder
High-quality Titan extruder
Very easy to upgrade your printer.
Suitable use for Remote and Short..
₹408
Brand: Import Dukan
Model: ID-06-502
The LV8729 is a PWM current-controlled micro step bipolar stepping motor driver. It is a best-suited Moter Driver for the Nema stepper motor whose current is less than 1.5A, which makes the motor steady, quiet, and precise.
Features:
Adaptive for driving below 6V-36V 2.5A stepping motor,
..
₹377
Brand: Import Dukan
Model: ID-06-221
The RAMPS (RepRap Arduino Mega Shield) is an all-in-one design to fit the necessary components for a 3D printer into one plug in shield for an Arduino MEGA. The plug in shield design includes plug in stepper drivers and extruder control electronics sockets for easy service, part replacement, upgrade..
₹276
Brand: Import Dukan
Model: ID-06-431
This is E3D Copper Heating Block mainly used for 3D printers.
Features:
Type: Heated Block
Material: Brass
It is used for 3D printers.
Package Includes:
1 x E3D Copper Heating Block..
₹229
Brand: Import Dukan
Model: D-6446
This is a 20T Bevel Gear 8mm Bore 90 Degree Direction. It only can fit 2 module gears, inner diameter is 8mm. Every 2 can be matched together to form a 90-degree transmission structure
Features:
No. of Teeth: 20 Teeth
Material: The silver gear column of this gear is iron, but the black ge..
₹142
Brand: Import Dukan
Model: ID-06-381
3D Printers Printer Stepper Mute Filter Module Protector Stepstick Smoother can effectively eliminate low-speed non-uniform waveform signals so as to achieve a relatively flat signal waveform.
Features:
Plug and work, no wiring required
Effective to use.
The effect is most obvious with ..
₹112
Brand: Import Dukan
Model: ID-05-859
Presenting the ultimate in precise motion control: the 2GT Ring Closed Synchronous Belt Rubber Transmission 160-10MM. This premium synchronous belt is designed to function at its best in a range of situations.
The 2GT Ring Closed Synchronous Belt, which was designed with longevity and efficiency ..
₹108
Brand: Import Dukan
Model: C-6219
This expansion board as a driver expansion board can be used for laser engraving machines, 3D printers, CNC. It is a total of four slots, can drive four A4988 stepper motor. Each road stepper motors only need two IO ports. In other words, six IO ports can be well managed three stepper motors.
The..
₹97
Brand: Import Dukan
Model: ID-06-603
5V 3007 Cooling Fan is a small but powerful fan. It maintains the temperature of the extruder, which results in good heat dispersion and wonderful performance.
The cooling fan operates on a 5V DC power supply which can be easily powered from the RPI board. It has a 2 pin JST connector to easily ..
₹91
Brand: Import Dukan
Model: ID-06-418
TL-Smoother V1.0 is an addon module for 3D printer stepper motor drivers. It provides flyback diodes for the motor outputs so that they are also protected against induction voltages in the unpowered state of the driver. It can eliminate the uneven signal wave at low speed so as to achieve the effect..
₹77
Brand: Import Dukan
Model: ID-06-270
SK10 10mm Linear Bearing Rail Support is usable with any 10mm linear guide, you can simply slide the rail through, then tighten the clamp screw at the top to fix it in place.
If you need to disassemble or otherwise repair your robot or machine, it's easy to open up the clamp and remove the rail.
..
₹75
Brand: Import Dukan
Model: ID-06-601
12 V 6010 Cooling Fan is a small but powerful fan. It maintains the temperature of the extruder, which results in good heat dispersion and wonderful performance.
The cooling fan operates on a 12V DC power supply which can be easily powered from the RPI board. It has a 2 pin connector to easily c..
₹72
